I Tested And Reviewed 10 Best Pump For Lake Water Irrigation (2023)

The Superior pump is a well-built piece of equipment that offers durability and reliability. One of the standout features is the brass impellor, which sets it apart from other pumps on the market. Despite its heavy build, it is surprisingly easy to install, thanks to the two slots on the base that allow for easier alignment with bolts.

The motor of the pump is remarkably quiet, unlike many other lawn pumps that tend to be noisy. This makes it a great option for those who value a peaceful and noise-free environment. Additionally, the pump comes ready for 220 volt use, but it can easily be switched to 110 volts if necessary.

One user noted that they coated the motor with Boeshield T9, a wax coating, to prevent rust. This is especially important for those who plan to install the pump outside, as it will be exposed to rain and sprinklers. However, it is essential to ensure that the motor is dry and not running before applying the coating.

The pump performs exceptionally well for irrigation, even with a lift of 18ft. It provides plenty of water and is worth the investment. In fact, one user mentioned that it outperformed their previous pump, which was more expensive but did not pump as much water.

Another user replaced a Gould Pump with the Superior pump after only 26 months of service. They were initially loyal to the Gould brand but were disappointed when the motor failed. Instead of replacing the motor, they opted for a new pump and chose the Superior pump. They found that it was well-constructed and seamlessly fit into the same place as the previous pump without requiring any adjustments to the plastic piping. After three months of use, they confidently recommend the Superior pump.

Lastly, a user purchased this pump to replace an old one that had burned out. They have a large property with a drip system that requires water from a lake for irrigation. Despite the size of their property, the pump has no problem providing great water pressure to all sections, even those in the very front. Overall, they are highly satisfied with the performance of the pump.

I was initially concerned about the performance of this pump due to the lack of detailed specifications provided. However, I needed a pump that could handle a vertical lift of 40 feet from the lakeside and a distance of 150 feet through garden hoses to our home and lawn. To set it up, I ran a 75" extension cord from the back of the house down to the lake and connected the pump on the shoreline. I used three 5/8" garden hoses to cover the 150-foot distance, and a 5/8" 15' garden hose with a small foot valve for the intake.

After priming the pump and turning it on, I quickly realized that the sprinkler's spray was disappointingly weak, only reaching about 10 inches. Frustrated, I checked for any kinks in the garden hose but found none. I began to doubt the pump's capabilities. However, upon inspecting the sprinkler inlet, I discovered a clogged screen/washer where the hose screws on. Once I removed the screen, reconnected the hose, and restarted the pump, the sprinkler started spraying above the roof with a significant amount of force. It provided the necessary power for a single sprinkler and could likely handle a couple more.

Although I haven't used the pump for an extended period, so I cannot speak to its longevity, I am satisfied with its performance so far. It delivers the necessary power to pump water uphill and provides a quiet operation. Surprisingly, it also comes with a pressure gauge, which was a pleasant surprise.

In addition to using it for watering our lawn, we have also placed this pump on our dock to transfer water from the lake to water our flowerbeds in the backyard. The pump's pressure is fantastic and meets our needs perfectly.

One important tip I would like to share is to remember to drain and bring pumps like this indoors during the winter. Unfortunately, we forgot to do so last year, and our old pump was ruined due to the freezing water. As a result, we had to purchase a new pump this summer. It was a valuable lesson learned from our mistake.

I recently purchased the FOTING Well Pump to transfer water from a stream to my ½ acre garden. The user manual provided with the pump was incredibly helpful and easy to understand, making the installation process trouble-free. We followed the instructions to set up the prime and also added a foot valve to the intact hose, which eliminated the need to prime the pump before each use. This feature alone saved us a lot of time and effort.

We were able to run two sprinkler heads from the pump, and I must say, the pump proved to be highly efficient and powerful. It delivered excellent water pressure without causing any noise disturbances. I was pleasantly surprised by its performance.

The pump arrived a day earlier than expected, which was a pleasant surprise. The installation process was straightforward, and once it was up and running, it provided a quiet and consistent water flow with great pressure. I couldn't be happier with its performance.

However, I did experience an issue with the pump after a few months of use. It stopped working, but the customer service team was quick to respond and offered me a refund. I am very satisfied with their prompt and helpful service.

Upon inspection, the pump appeared to be well-built and sturdy. It's possible that I received a defective unit, as it worked perfectly fine until it stopped functioning last week. I believe this may have been a quality control issue, but I appreciate the company's willingness to replace the defective pump. Their responsiveness has left me extremely impressed and thankful.

I have been using the Merrill MFG FVNL100 1" No-Lead Brass Foot Valve for my watering and sprinkler systems, sourcing water from a lake with lily pads and small debris. I have built a 45-gallon filter with this foot valve in the lake, and it has been working well for the past month.

One thing I would recommend is having an "open" valve at the top of your water source for easy priming of the pump. It can be inconvenient to have to remove the screw to fill it up every time. Additionally, it is important to prime the pump fully and remove all air before turning it on to avoid potential damage to the bearings and prolong the life of the pump.

I have been running the pump daily, pumping water from the lake through a 1" inlet (approximately 35 ft from the foot valve to the pump), and then another 200-250 ft after stepping down the size to 3/4". I am planning on extending the 1" outlet for more zones as the proof of concept with this pump seems to be working well.

In terms of noise, the pump is not very loud. You can hear it, but only from about 15-20 feet away. If it were covered, it would likely be even quieter. I am planning on covering the pump with a small wood structure to keep the rain out while ensuring adequate airflow.

I am satisfied with this pump for now and will continue to monitor its performance. Overall, it has been a cost-effective solution compared to the expensive alternative of replacing an old jet pump with a tank. With just $200 for the pump and $50 for the necessary pipe and fittings from the hardware store, I have achieved a nicer setup and even added a hose bib for washing down the concrete floor in the springhouse.

Although I have only used the pump for about an hour so far, it has performed excellently with the head pressure on the suction. I am hopeful that it will continue to work great in the future.

The durability and power of this booster pump make it an excellent choice for various applications. With its included controller, it can easily be connected to an outdoor faucet. Not only does it have enough power for garden irrigation, but it can also be used for well pumping and pool pumping, showcasing its versatility.

One of the standout features of this pump is its quiet operation, which sets it apart from other models. However, a minor drawback is that the fittings are a mixture of metal and plastic, which may not be preferred by some users, especially if the pump needs to be frequently moved or taken on and off. While this is a personal preference, it's worth mentioning for those who prioritize all-brass fittings.

The pump is particularly useful for vegetable garden irrigation, eliminating the need for manual water pumping. The stainless steel casing instills confidence in its quality and durability, suggesting that it will continue to function effectively for a long time.

Despite its small size, this pump packs a powerful punch. Its 1" inlet and outlet, along with the included fittings, make it convenient to use. The pre-wired controller adds to its ease of operation, allowing it to start pumping as soon as it is filled with water.

This pump has proven to be a game-changer for increasing irrigation coverage in small pastures. It works well with sprinklers using 1-inch input, and while it can also be used with 3/4" hoses, the coverage may be slightly reduced with the smaller diameter hoses. Its ability to operate under extreme conditions, such as the excessive heat of Texas, is commendable.

An added advantage of this pump is its automatic shut-off feature. If the water supply is accidentally cut off, the pump stops after approximately 10 seconds, preserving its integrity. This is especially useful in scenarios where interruptions in the water flow may occur.

I have been using the Wayne PLS100 irrigation pump for four years now, and I must say it continues to impress me. Despite a slight decrease in pressure, it still delivers 68psi at the end of a 75' hose. This decrease is hardly noticeable when you see how much water it throws from the sprinkler. It is a great investment that has proven its worth over time.

I initially purchased the Wayne PLS100 to pump lake water for irrigating my Bermuda and zoysia grasses. After extensive research, I chose the Wayne over cheaper off-brand models, and I'm glad I did. The pump is simply amazing. I used a 1" brass foot valve on the intake hose and primed the pump according to the manual. Once I flipped the switch, it took about 25 seconds for the oscillating sprinkler at the end of the hose to start throwing a 50' wide shower of lake water 75' away, 10' above the intake. The spray spread was almost as good as what the house bib produced. I was thoroughly impressed.

The pump is relatively quiet, especially when used outdoors. However, if it's located near a living area, it would be wise to create an insulated and ventilated box for noise reduction. Personally, I have had no issues with noise as I positioned the pump away from living spaces.

Curious to test its capabilities further, I added a splitter at the 75' point and attached a 25' hose to each end with oscillating sprinklers. While there was a slight decrease in water force, it was still sufficient for watering. Moving the splitter, hoses, and sprinklers to the front yard resulted in a further decrease in spray from the sprinklers. However, even with both sprinklers in-line, the total coverage of approximately 1200 sq ft was adequate.

To improve convenience, I swapped out the 1" intake hose for a 30', 3/4" hose to position the pump closer to the power source. Surprisingly, there was no discernible loss of water pressure at the 150' point. I confirmed this by borrowing a psi gauge, which showed a consistent pressure of 78 psi straight from the pump's outlet, 76 psi at the 75' point, and 63 psi at 150' (22' above intake).

I recently purchased the Eco-Worthy pump and I must say, I am quite impressed with its performance. One of the standout features of this model is how quietly it runs. Unlike previous models, it comes with two adapters and white tape, which allows for easy connection to regular garden hose connectors without the need to search for additional parts.

In terms of water pressure, it may not be as strong as city water, but it is certainly powerful enough for my needs. I am able to effectively water my lawn, trees, and garden from a distance of about 20 to 30 feet. The pump itself feels solid and durable, although I cannot comment on its long-term durability as I have only just started using it. However, I am reassured by the fact that it comes with a four-year warranty, which is the longest warranty I have ever seen for a small pump.

One important tip to remember is to use the white tape provided to wrap around the connectors multiple times to avoid any leaking issues. This simple step can save you from potential headaches down the line.

I also appreciate that the package includes two 1/2" barb end pipe adapters and a brass 1/2 inch male and female x 3/4 inch Garden Hose Thread adapter. These fittings have proven to be very handy and have reduced the need for additional purchases.

Compared to my existing diaphragm pump, the Eco-Worthy pump not only provides more flow and pressure capacity but also operates at a lower noise level. Additionally, the pump comes with a 5-foot long AC cable, which is longer than what I had previously. The only minor drawback I have noticed is that the pump unit appears to be front head heavy, causing it to tip forward unless it is anchored to something.

In terms of customer service, I had a positive experience. I reached out to them regarding an issue with the strainer cap bursting, and they promptly responded and are sending me replacement filters. This level of care and support speaks highly of the company and I highly recommend both their products and this pump.

I recently purchased this pump as a replacement for a more expensive model that was damaged during a flood. I must say, I am impressed with the quality and performance of this pump, especially considering its affordable price. The plastic pump housing makes it much lighter and easier to handle compared to my previous heavy-duty pump.

I have a large sprinkler system covering a 2-acre area, and this pump supplies it with ease. It operates quietly, which is a major plus. However, I did encounter a slight inconvenience during the installation process. The wiring connections are located very close to the conduit connection point on the motor housing, partially obstructing the opening. This made it challenging to fish in the wires and connect them to the terminals. It would be great if the connection screws were moved further away from the conduit connection point to simplify this process.

Despite this minor issue, I am overall satisfied with my purchase. I was initially hesitant to order this pump online, as I prefer buying such items in-store to facilitate returns if necessary. However, the convenience of Amazon Prime's fast delivery outweighed my concerns, and I received the pump within just 2 days.

I have only installed the pump recently, but I have been running it continuously for almost a day now, and it is performing well. If any issues arise in the future, I will update my review accordingly.

Update (10/14/2016): It has been two years since I purchased this pump, and it is still going strong. I have used it extensively to pump water out of my ditch, and it has proven to be a reliable and powerful machine. In fact, it provides better pressure to 8 impact sprinklers than my house water does to just one. This pump is truly a beast and has surpassed my expectations.

During the initial testing phase, I powered the pump using a 10-gauge extension cord connected to an outdoor outlet. It worked perfectly fine on a standard 20A breaker, as long as there were no other loads on the circuit. I was able to run eight standard impact sprinklers without any issues. The pump was always primed since it was a few inches below the water level, but I did notice some cavitation noise from the impeller when there was minimal restriction on the outlet. However, the outlet pressure seemed consistent with the specifications.

Throughout the summer, I used the pump for an average of 50 hours per week, and it showed no signs of wear or decline. I am extremely satisfied with this pump and highly recommend it.

I have been using this pump to water my lawn and I am very satisfied with its performance. I am pulling water from behind my house and using a 200-foot hose up a 10-foot incline, and the pump is able to pump water with no problem.

I purchased this pump along with an adapter that took the 1" outlet down to a 3/4" garden hose. I hooked up 125 feet of 3/4" garden hose, with 100 feet of it running up a slight hill. The pump worked well with both the impact sprinkler and the oscillating sprinkler, providing a similar water supply as the yard hydrant that gets its supply from the same pump. However, I was expecting a bit more power from a 1.6 HP pump. The flow and pressure were just about as good as the house water, but I had hoped for better.

After considering the length and diameter of the hose, I decided to try using a 1" garden hose instead of the 3/4" hose. I ordered a 100-foot 1" garden hose, which was more expensive than the pump itself. However, it was worth the investment. Now with 100 feet of 1" hose running uphill, the power of the pump has significantly increased. The water shoots out with great force and enthusiasm, providing better flow and pressure.

In order to save money, my next plan is to use black 1" poly water line instead of the expensive 1" garden hose. Lowe's offers 100 feet of black poly pipe at different price points, with the cheapest option being adequate for this purpose. This will be a more cost-effective solution, especially if you have an out-of-the-way run or can bury it.

I have been using the Wayne pump for three seasons now, and I have to say that it has exceeded my expectations. I had previously owned a Wayne pump that served me well for many years, so when it came time to replace my old pump, I decided to stick with the brand.

Installation was a breeze, and I was able to wire the pump for 240 volts and install a low-pressure shut-off switch to ensure the pump shuts off if the ditch runs out of water. This added feature has been a lifesaver, as it helps protect the pump from unnecessary wear and tear.

Irrigating from a ditch system that carries water from the river means dealing with silt and debris during spring runoff and heavy rains. Despite these challenging conditions, the Wayne pump has held up remarkably well. It still pumps the same volume of water as it did when first installed, and I haven't experienced any issues or malfunctions.

To ensure I have a backup plan in case the impeller fails, I ordered a spare from Wayne. The replacement process is straightforward and easy to do on my own. Knowing that I have a spare on hand gives me peace of mind.

One thing I've learned from my previous pump experiences is the importance of monitoring the system's status. There are many factors that can affect the pump's intake and prime stability, so regular monitoring is crucial. Occasionally, my pump loses prime and runs semi-dry all night, which is less than ideal. However, with the Wayne pump, I have not encountered this issue.

The pump itself is solidly constructed and has worked flawlessly as part of my maintenance routine. The only difference I noticed is that it does not have a plug for priming. However, I have added a 3/4" fitting and ball valve to the intake pipe, which allows me to prime the pump easily if needed. So far, I haven't had to use it, but it's good to have as a backup plan.

I have also taken precautions to ensure trouble-free irrigation during the winter months. I use an auto temperature-sensing heater rope around the pump, which has proven effective in preventing freezing and cracks in the housing. Draining the pump in the past has caused issues, so this method has been a game-changer for me.