I Tested And Reviewed 7 Best Glass Cutter For Stained Glass (2023)

I recently purchased this bottle cutter after being inspired by @a_dad_called_brian on TikTok, who creatively transforms old bottles into drinking glasses and utensil holders. Initially, I was excited to try it out, but I encountered a few challenges along the way.

The directions provided with the product were lacking in clarity and detail. My son and I even attempted to make a video review, but unfortunately, we got carried away and forgot to record most of it. However, through trial and error, we were able to figure out the process.

Our first two attempts using older wine bottles from the 90s proved unsuccessful. These bottles had been stored and transported for about thirty years, resulting in a less-than-clean break. Thankfully, I was able to salvage one of them using the included glass cutter, but the other bottle cracked all the way down.

On our third attempt using a new dark glass bottle, we finally achieved success. Here are some straightforward instructions that we found to be effective:

1. Begin by mounting the L-Bracket to your desired cup height.

2. Place the bottle on the rack and roll it around against the cutter.

3. Apply rubber bands of the correct size, placing one on each side of the etched ring.

4. Pour boiling water over the bottle, ensuring that the entire glass is not covered, for approximately 15 seconds.

5. Quickly follow by pouring iced water over the bottle for about 15 seconds.

6. Repeat steps 4 and 5 until the bottle breaks on its own.

7. Finally, sand down the edges of the glass.

Although the product worked well overall, I do have a few suggestions for improvement. Firstly, it is crucial to ensure that all components are securely fastened before cutting the bottle. This will prevent any unwanted movement of the cutter during the process. Additionally, the sandpaper included with the bottle cutter could be of better quality. To compensate for this, I have ordered a set of 1,000-3,000 grit sandpaper from Amazon, as recommended by the TikToker I mentioned earlier.

One key tip for success that I discovered is to have rubber bands on both sides of the cut. This helps to maintain stability during the boiling and cooling process. When pouring boiling water, it is essential to be cautious and ensure that the entire glass is not covered, as this can lead to the bottle shattering. With a little bit of pressure, gently pull the two sides of the bottle apart while pouring cold water between the rubber bands.

After using this glass cutter for 11 months, I have revised my rating from a 5 to a 3. Initially, I was impressed by the positive reviews and decided to add oil to the cutter. However, today when I tried to use it, the cutter fell apart in my hand when I applied a slight amount of pressure. The adjustable saddle and the top of the oil reservoir broke apart. Despite this, I still recommend this cutter, but I advise against adding oil to the reservoir. Instead, keep the oil in a separate cup and dip the cutter in it.

I must commend the manufacturer's customer service. I contacted them and they promptly replaced the cutter free of charge. This demonstrates excellent customer service.

One of the standout features of this cutter is its ease of use. It fits comfortably in my hand and effortlessly cuts through glass. It is particularly suitable for individuals with carpal tunnel issues or arthritis, as it is easier to hold compared to larger cutters. Personally, I have experienced relief from the pain and numbness in my hand and fingers when using this cutter.

As a newcomer to mosaics, I initially struggled with a lower quality cutter from a hobby store. However, after purchasing this cutter, I was amazed by the difference it made. I can now score the glass with ease, without applying excessive pressure or causing splintering or breakage in unintended areas. This has saved me money by preventing mistakes on my projects.

The grip of this cutter is another feature I appreciate. It fits comfortably between the thumb and index finger, requiring minimal pressure to operate effectively.

After trying out this bottle cutter, I have some valuable insights to share. Firstly, it is important to practice on a few bottles before attempting to cut the ones you really want to work with. This will help you get the hang of using the cutter effectively.

I found that the bottle cutter works best on vertically straight bottles such as Pinot bottles. Flared bottles can be a bit more challenging to cut accurately because the rollers are designed to work best with straight bottles.

When using the cutter, be careful not to press too hard into the blade while rotating the bottle. Applying excessive pressure can cause the cutting line to be off-center.

If you are cutting a wine bottle with a paper-affixed label, it is a good idea to wrap the label portion in plastic wrap first. This will protect it from the hot and cold water during the cutting process.

Instead of trying to force the separation, I recommend alternating between hot and cold water to gradually separate the cut sections. With patience and persistence, the bottle will eventually separate.

When applying the hot and cold water, make sure to aim the opening of the bottle away and down. Accidentally getting water inside the bottle can lead to cracking the bottom of the bottle.

It is also important to note that safety glasses should be worn while using the bottle cutter. Additionally, it is advisable to use the cutter outdoors to avoid any mishaps with glass shards on your kitchen counter or floor.

I recently purchased this glass grinder as a replacement for my old one, and I am extremely satisfied with its performance. My previous grinder, which was over 20 years old, had become quite ineffective. However, this new grinder has proven to be a worthy replacement.

One of the things I love about this grinder is its compact size. It is not overly large, making it easier to handle and store. Despite its smaller size, it does an excellent job of grinding glass. The setup process is simple and straightforward. All you need to do is fill the base with water, place the top cover on, and you're ready to start grinding.

The self-watering feature of this grinder is a major advantage. Unlike other grinders that require a sponge, this one keeps the glass and grinder wet automatically. This saves time and effort, allowing for a smoother grinding experience.

I must also mention the exceptional customer service I received when I had a query. The company promptly addressed my concern within hours, which speaks volumes about their commitment to customer satisfaction.

I recently purchased this glass cutting tool and I must say, it is quite impressive. I have tried other types in the past, but none of them worked as effectively as this one. It is definitely a great tool for cutting glass.

One of the things I really like about this tool is its ability to hold small circles in place. I have placed a small piece of a drawer liner in the center, which provides a good grip for the glass and prevents it from moving while cutting. This feature has been very useful for me.

However, there are a few minor issues that I encountered, which is why I am giving it 4 stars instead of 5. Firstly, inserting the arm into the hole in the post was a bit difficult initially. However, after some effort, it eventually went in and now it goes in and out easily enough.

Another issue I found was with the ruler on the arm. It is incorrect and confusing as the cutting blade is not at the zero point. To overcome this, I recommend using the ruler on the base instead, which is accurate and easier to follow.

Additionally, I noticed that while cutting, you need to hold the glass firmly in place. It would be helpful if the tool had rubber feet to provide better grip, as some other reviewers have also mentioned.

I had always struggled with cutting glass until I came across this amazing glass cutter. I had tried using a hardware store glass cutter, but it never seemed to cut in the right place and would often result in broken glass. However, when I reluctantly decided to purchase this cutter, I was pleasantly surprised by the results. The first cut I made was perfect, and subsequent cuts have been just as flawless. What's even better is that I don't need to apply as much pressure as before. This cutter has truly made glass cutting a breeze for me.

Before purchasing this cutter, I had tried various other brands, including a common "key" type and a pencil type brass oil feeding cutter. Unfortunately, these cutters didn't work well with the glass I was trying to cut, especially when it had dips and bumps. After watching several videos, I noticed that most people were using Toyo cutters, particularly the pistol grip ones. I decided to give it a try, and it has been a game changer for me. The comfort and grip of this cutter make it easy to apply pressure at the right area, angle, and amount. It has also improved my ability to guide the cutting head along pattern lines. I have even set aside my old hardware store cutter and plan on buying a spare cutting head for this one. I am now a true fan of Toyo cutters and have become interested in the larger head for cutting thicker glass.

These cutters are simply amazing. I highly recommend upgrading to this cutter and investing a little more money. It is worth every penny and is far superior to cheaper brands. With proper care, this cutter will last a long time. In fact, I am now considering purchasing a larger head for thicker glass. Don't hesitate to make the switch to this cutter – you won't be disappointed.

I recently used these cutters to rehab our 1910 wavy glass windows and they were a lifesaver. We struggled initially to find the best techniques for cutting new panes from salvaged sash, but once we started using the Toyo cutter, everything became much easier. We started with a cheaper pen-type cutter, but quickly realized that investing in a quality tool was essential. The TOYO brand is excellent, albeit a bit pricier, but what I really appreciate is the ability to replace the cutting wheel without having to buy a whole new handle. This cutter works perfectly with any cutting oil brand we've used. The pistol grip design provides better control and leverage, especially when scoring away from yourself. Trust me, give it a shot!

I am extremely satisfied with this glass circle cutter. Initially, there was some confusion on how to make the suction work, but once I figured it out, it worked like a charm. Contrary to the negative reviews, this cutter is not designed to cut all the way through the glass. Instead, it scores the glass, and then breaking pliers are used to complete the cut. The suction on this cutter is excellent, especially when the tab is held down while cutting. I have experienced no issues with it and am pleasantly surprised by how well this product performs. I highly recommend it.

I purchased this glass cutter to make a circular lens for a can light in my house. The original glass was not allowing enough light through, so I decided to find an affordable solution instead of paying a glass company $40 to cut an 8" diameter piece of glass. This cutter, priced just over $10 on Amazon, turned out to be the perfect alternative. Before using it, I watched a helpful YouTube video on how to cut circular glass and used an old piece of glass from a picture frame for practice. The cutter worked flawlessly, and I have successfully made lenses for two lights so far. Not only does it work great, but it has also saved me a significant amount of money compared to using a glass cutting service. If you need to cut glass in a circle, I highly recommend this product. Just make sure to watch a YouTube tutorial if you're not familiar with glass cutting techniques.

I am extremely satisfied with the performance of this glass circle cutter. I use it frequently, and the results are consistently impressive. The cutter effortlessly creates clear, sharp circles, as shown in the attached pictures of a clear circle cut with this tool. I love how easy it is to use, and the adjustable size option is a great feature. It allows me to cut circles of various sizes, from small to big. I recently used it to cut larger circles, measuring 10 inches, for vases that I was making. The suction on this cutter is incredibly strong and does not move at all while scoring. It is even capable of lifting and shaking the glass without falling off until the little lever is released. This tool has become an essential part of my glass fusing supply kit, and I highly recommend it to anyone in need of cutting glass into circles.

I recently received the glass cutting tool kit and I must say, it exceeded my expectations. Although it is not specifically listed as a tool kit, it does come with a total of 9 pieces, making it a great value for less than $16. The kit also comes in a convenient zippered nylon case, with individual slots for each tool and even a couple of extra empty spaces for customization.

One of the standout features of this kit is the weight and feel of the glass cutter. It has a good heft to it, which makes it much easier to control your cuts. The blade itself is exceptional, cutting through glass like butter. Even as a beginner, I found it simple to get a feel for the tool and achieve precise cuts. It truly is an awesome glass cutter.

Comparing this kit to others on the market, the value becomes even more apparent. Most listings I came across were priced at twice the amount and only included 2 or 3 pieces. In contrast, this kit offers a total of 9 tools. In fact, I found the exact same tools being sold individually for over $75! This makes it a no-brainer for anyone looking for an affordable and comprehensive glass cutting solution.

In terms of performance, the kit delivered as promised. The glass cutter performed flawlessly, and the other tools in the set did their job effectively. I haven't had the chance to test their long-term durability yet, as I have only used them for a couple of projects, but they have proven to be reliable and met all my needs.

I do have one minor suggestion for improvement. It would be helpful if the kit included some oil for the cutter. However, this is a minor inconvenience and does not detract from the overall performance of the kit.